Railway Engineering

-
Railway Engineering

Introduction to Railway Engineering

 History of Indian Railways-
Component parts of railway track, 
Wheel and axle arrangements, 
Coning of wheels, 
Various resistance, and their evaluation, 
Hauling capacity, 
Tractive effort, 
Stresses in railway tracks, 
Stresses in rail, sleepers, 
Stresses in ballast, Formation.

Unit 1& 2 Notes:



*Ref: Indian Railway

 Geometric Design:

  • Alignment, 
  • Horizontal curves, 
  • Superelevation, 
  • Equilibrium cant and cant deficiency, 
  • Length of transition curves, 
  • Gradients and grade compensation, 
  • Vertical curves.


.........

Comments

Post a Comment

Popular posts from this blog

Design of Concrete Structures - II: Multiple Choice Questions (MCQ) & Answers

-
Image
  Unit 1: Staircases (Limit state method) Multiple Choice Questions 1.       The effective span of the staircase supported at top and bottom risers by beams spanning in parallel with the riser is A.      Clear distance between beams B.      Distance between c/c of beams C.      Clear distance between beams + d D.      None of the above ANS: B 2.      If  R  and  T  are rise and tread of a stair spanning horizontally, the steps are supported by a wall on one side and by a stringer beam on the other side, the steps are designed as beams of width A.      R + T B.      T – R C.  √ ( R 2   +T 2 ) D.      R - T ANS: C 3.      If  T  and  R  are tread and rise respectively of a stair, then A.      2R + T = 60 B.      R + 2T = 60 C.      2R + T = 30 D.      R + 2T= 30 ANS: A 4.       The minimum head room over a stair must be A.      200 cm B.      205 cm C.      210 cm D.      230 cm ANS:   C 5.       The number of treads in a flight is equ
Read more

DESIGN OF CONCRETE STRUCTURES - I MCQ's

-
Image
  DESIGN OF CONCRETE STRUCTURES - I MCQ   Unit 1: Introduction  1) The maximum compressive strain in concrete in axial compression is taken as  A. 0.001  B. 0.002  C. 0.003  D. 0.040  ANSWER: B  2) The flexural strength of concrete is given by  A. 0.6√fck  B. 0.7√fck  C. 0.5√fck  D. 0.8√fck  ANSWER: B  3) Tolerance on placing the reinforcement for effective depths 200 mm or less is  A. +/-5mm  B. +/-6mm  C. +/-8mm  D. +/-10mm  ANSWER: D  4) Tolerance on placing the reinforcement for effective depths more than 200 mm is  A. +/-5mm  B. +/-6mm  C. +/-8mm  D. +/-10mm  ANSWER: A  5) The minimum frequency of sampling of concrete of each grade for 1-5m3 shall be  A. 1  B. 2  C. 3  D. 4  ANSWER: A  6) The minimum frequency of sampling of concrete of each grade for 51m^3 and above shall be……samples.  A. 4 + one additional for each 50m3  B. 5 + one additional for each 50m3  C. 6 + one additional for each 50m3  D. 4 - on
Read more

What is the formula for taking load from two way slab for beam design?

-
Image
How to calculate load from two-way slab on beam? As per Clause No  24.5 of IS 456: 2000 , the loads on beams supporting solid slabs spanning in two directions at right angles and supporting uniformly distributed loads, may be assumed to be in accordance with following Fig. Let us consider the following example: ABCD is a two-way slab ( L/B = 1.5<2 ) Assume: Dead load of slab : 0.125 x 25 = 3.1255 kN/m^2 (100 mm thick slab) Live load on slab : 3 kN/m^2 Total load = 5.5 kN/m^2 Now for finding force on beam BC the load will come from the triangular hatched part of slab So we multiply the load by vertical length of triangle to get load on beam per unit length 2 ∗ 5.5 = 11 k n / m 2 ∗ 5.5 = 11 k n / m fig (b) shows the disribution of load on beam BC ( same will be for beam DC ) (If we convert this load on beam as uniform load we will get maximum bending moment of 11 kN/m but now as we have considered this load in form of triangle so we will get a max
Read more